No products found with current parameters. Try to go back and adjust/reset the filters or select another product category below.
2/2 way solenoid valve with 3/4 inch threads and 230V AC coil. Normally closed (opens when energized). Suitable for clean media (max 130°C) and an operating pressure of 0.5-16 bar (indirect operated). Brass housing with EPDM seal. The orifice is 20mm, the Kv-value is 6.4m3/h (106.7 l/min at dP=1 bar, water).Including coil and DIN-A connector
Order before 16h CEST (mo-fr), same day shipment
2 year warranty, Returns 30 days
Indirect operated 2/2 way JP Fluid Control solenoid valve with brass body, 3/4 inch threads and a 230V AC (50Hz) coil. The circuit function of the solenoid valve is normally closed (opens when electrically energized). Suitable for systems with an operating pressure of 0.5 bar to 16 bar and a maximum temperature of 130 °C. For proper operation, this indirectly operated valve requires a positive differential pressure of 0.5 bar. For a closed system, such as a cooling unit, a directly operated valve or an electric ball valve is more suitable. The orifice is 20 mm and the Kv-value is 6.4m3/h. The Kv-value is used to calculate flow rate: at 1 bar differential pressure (water) the flow rate is approximately 106.7 l/min.
This valve has an EPDM seal, which is suited for (hot) water, steam and most basic substances. For oils, compressed air and fuels, FKM is recommended instead of EPDM.
Please consult the chemical resistance chart for other media.
The coil (type CS1-230AC) DIN - A with connector is provided with the valve. Other connector types, such as with an LED indicator can be ordered separately. The coil can easily be mounted on the valve. Never connect the coil to the power supply when it is not mounted on the valve to prevent the coil burning out.
Solenoid valves are electrically controlled valves which open or close by means of an electric current through a solenoid (coil). As long as they are electrically energized they consume energy. They open and close quickly. They are sensitive to dirt and can only be used with clean liquids or gases.
|Solenoid Valve||Electromechanically operated valve. An electric current through a solenoid is used to open or close the valve.|
|Indirect operated||Indirect or servo operated solenoid valves use the differential pressure of the medium to open or close the valve. The minimum differential pressure is usually 0.5 bar. Since the fluid pressure is used, a relatively small coil can operate a large diaphragm and thus a high flow.|
|2/2-Way||2 ports (inlet and outlet) and 2 positions (open and closed).|
|Normally closed||The valve opens when the coil is energized (Normally Closed or NC).|
|EPDM||EPDM is used for the seal material. EPDM is suitable for (hot) water, steam, and alkaline substances such as detergents. For other media FKM (Viton) is usually a more chemically resistant and durable alternative. View the materials compatibility overview.|
|230V AC||230 volt AC (50Hz). For most valve types different coils are available (380VAC, 230VAC, 120VAC, 24VAC, 12VDC, 24VDC). Always use the correct power supply.|
|Kv-value||Flow (m3/h) water of 20°C through the valve at a 1 bar pressure drop. The flow can be calculated with the formula: Q=Kv√dp. Example: The flow of a valve with Kv=0.5 in a system with a 2 bar inlet pressure and a free outlet can be calculated with: 0.5√2=0.7 m3/h, or 12 liter/min. For gases another formula must be used, the flow rate will be higher. A handy tool to determine the required Kv value is our Valve Sizing Calculator.|
|3/4 inch||G3/4 inch pipe thread (BSPP). Determine the valve size based on the desired flow rate and pipe diameter. Using the range of fittings, you can connect the valve to the desired type of pipe.|