2 Way electric PVC ball valve with 63 mm solvent sockets and powerful and energy efficient 230V AC/DC actuator (max 20Nm). Media from 0 to 60°C, max pressure 16 bar at 20°C. PVC valve housing with PVC ball and EPDM valve seats. The nominal diameter is 50 mm (full bore), the Kv-value is 186m3/h (3100.1 l/min water at dP=1 bar). 3-point control. Rotation 0-90° in only 4 sec. Compact and strong actuator housing (IP67) with position indicator. Manual override function and two extra limit switches for position feedback.
This strong and energy efficient 2-way electrical ball valve from Tameson can be used to automatically shut of pipes with gas or fluids. The valve has 63 mm solvent sockets with a true union design (full port). The housing of the valve is made of PVC with a PVC ball and EPDM sealing. The actuator is suitable for power supplies from 100 to 240V alternating current (50/60Hz). The actuator has a robust aluminium housing (IP67, provided that an appropriate cable is connected) and delivers a max torque of 20 Nm. Rotation of 90 degrees (close to open) in 4 seconds. When the ball reaches an end position, the electric motor is turned off and no energy is consumed. The actuator is equipped with two additional limit switches for position-feedback. The limit switches are positioned at 0 and 90 degrees. If required, the angular position of the switches can be adjusted by the user. A mechanical position indicator on the top of the actuator shows the valve position. The actuator is equipped with a manual override.
|Actuator ref:||AG-020-A||Ball Valve ref:||6P14P063|
|Voltage:||100-240V AC (50/60Hz)||Housing:||PVC|
|Nom./Max. Current:||0.1/0.2 A||Ball:||PVC|
|Duty Cycle:||S2 30min.||Connection:||63 mm solvent sockets|
|Open/Close:||4 s||Nominal Diameter:||50 mm (DN)|
|Amb. Temp.:||-1-10°C..50°C||Installation length:||178 mm|
|Range:||0-90°||Max pressure (@20°C):||16 bar|
|Extra limit switches:||2||Function:||2 way|
|Manual override:||Yes||Temp medium:||0°C..60°C|
This valve can be used in combination with gases and fluids. Some examples of compatible media are (waste) water, chloride solutions (seawater, swimming pools) and destilled water. PVC is not suitable for temperatures above 60°C. PVC is also suitable for many mild acids, alkalis and salt solutions. The maximum pressure at room temperature is 16 bar, at higher temperatures the maximum allowed temperature decreases. The direction of pressure is not important, the direction of flow may be in any direction. The temperature range of the medium lies between 0°C and 60°C. At high temperatures, it is recommended to install the valve in a ventilated area. It is allowed to install the valve in a humid environment provided that all parts, like an appropriate electrical cable, are correctly fixed. Ball valves can be used with light contaminated fluids. Some examples of applications for this valve are HVAC, irrigation, industrial automation, water management.
The actuator can be used with alternating current (50/60Hz) from 100 volt up to 240 volt. The actuator draws 0.1A nominal, and 0.2A at maximal torque. To connect a cable to the actuator, the cover needs to be removed with four bolts. The system operates with 3-point control. Terminal 1 and 2 are permanently connected to the power supply. Terminal 3 and 4 are used to close or open the valve. The signal (phase/null) to terminal 3 and 4 must be the same as terminal 2. Never connect 3 and 4 at the same time to prevent short circuit and damage. The actuator has two internal limit switches. As soon as the actuator's end position is reached (0 or 90 degrees), the motor turns off and no energy is consumed. In addition, in the actuator there are two additional limit switches for control purposes. The angular position of the limiti switches can be modified. Always connect the earth and do not use the pipes as ground.
Electrical wiring diagram of the AG-020-A actuator.
Make sure that the position of the ball and the actuator are properly set before assembly. The actuator is provided with two adapters to connect the actuator to the valve shaft. Mount the actuator to the valve with the provided bolts. There should be no play between both flange. Use our fittings range for the connection between the pipe and the valve.
Note: This product is delivered in separate parts, but with the required mounting accessories.`