Electrical Ball Valve BW2 1/2'' 2-way 230V AC 3-point

Electrical Ball Valve BW2 1/2'' 2-way 230V AC 3-point
Electrical Ball Valve BW2 1/2'' 2-way 230V AC 3-point
Electrical Ball Valve BW2 1/2'' 2-way 230V AC 3-point
Electrical Ball Valve BW2 1/2'' 2-way 230V AC 3-point
Electrical Ball Valve BW2 1/2'' 2-way 230V AC 3-point
Electrical Ball Valve BW2 1/2'' 2-way 230V AC 3-point
Electrical Ball Valve BW2 1/2'' 2-way 230V AC 3-point
Electrical Ball Valve BW2 1/2'' 2-way 230V AC 3-point
Electrical Ball Valve BW2 1/2'' 2-way 230V AC 3-point
Electrical Ball Valve BW2 1/2'' 2-way 230V AC 3-point
Reference: BW2-012-AW1-230AC
Brand: JP Fluid Control

2 way electrical ball valve with 1/2 inch female threads (BSP) and energy efficient 230V AC actuator. Suitable for liquids and gases (max 110°C) and a pressure from 0-10 bar. Suitable as zone valve in heating systems. The valve has a brass housing with chromed ball and PTFE valve seats. The nominal diameter is 12mm, the Kv value is 8.6m3/h (143.3 l/min at dP=1 bar, water). 3-wire connection (3-point): neutral wire and 2 control wires (to open/close). The valve opens in 16s.

Including actuator
View all
Regular price
$81.60
excl VAT

In stock +0 days On request On request
0 are currently in your cart. For orders exceeding 29, expect an increased lead time of 0 days. Up to 79 items available for online order. For higher quantities, please contact us on support@tameson.com to request the lead time. The item is not available for online order, please contact us on support@tameson.com to request the lead time.


Shipping to United States: $14.95
Free for orders > $390.00
Expected delivery in 2 - 3 business days

Description
Specifications
Downloads
Related products

Very energy efficient and robust 2 way JP Fluid Control electric ball valve to open or close pipes electrically. The valve has 1/2 inch threads (female thread BSPP) and a 230V AC actuator (IP54). This valve is suitable for liquids and gases (-10 to 110°C) and is often used in heating systems. A ball valve is less sensitive to dirt than a solenoid valve. It is however recommended to install a filter before the valve. The valve body is made of brass, the ball is chrome plated and the seal is PTFE (Teflon). The orifice is 12 mm, the Kv-value is 8.6 (143.3 l/min at dP=1 bar). The time for opening or closing is approximately 16 seconds.

Installation

The actuator has a 3-wire connection, and must be connected as shown in the diagram below. The actuator is supplied with a cable. The actuator has 3-point control. One wire is permanently connected to the neutral. The other two wires are control wires to rotate the ball in both directions (connect to the phase). Please note: never connect the two control wires at the same time, this could damage the actuator! The actuators can be supplied with an integrated relay (On-Off control), in that case only one control wire is needed. The actuator includes limit switches, energy is only consumed during opening or closing of the valve.

jp-fluid-control-wiring-ball-valve-actuator-aw1-230ac.jpg

Important

  • Please observe the color coding of the wires. Never connect the two control wires at the same time, the actuator will be damaged.
  • Suitable for clean gases and liquids, including cold & hot water.
  • Make sure that the valve is suitable for the application and that the materials are suitable for the medium and the temperature.

Note: this valve is not suited for dry gases such as unlubricated compressed air.