Sorry for the inconvenience.
No products found with current parameters. Try to reset filters.
Solenoid Valve ST-DA 1/8'' brass FKM 0-13bar 230V AC
2/2 way solenoid valve with 1/8 inch threads and 230V AC coil. Normally closed (opens when energized). Suitable for clean media (max 120°C) and an operating pressure of 0-13 bar (direct operated). Brass housing with FKM seal. The orifice is 3mm, the Kv-value is 0.2m3/h (3.3 l/min at dP=1 bar, water).Including coil and DIN-A connector
Order before 16:00 h, same day shipment
2 year warranty, Returns 14 days
Direct operated 2/2 way JP Fluid Control solenoid valve with brass body, 1/8 inch threads and a 230V AC (50Hz) coil. The circuit function of the solenoid valve is normally closed (opens when electrically energized). Suitable for systems with an operating pressure of 0 bar to 13 bar and a maximum temperature of 120 °C. The orifice is 3 mm and the Kv-value is 0.2m3/h. The Kv-value is used to calculate flow rate: at 1 bar differential pressure (water) the flow rate is approximately 3.3 l/min.
This valve has a FKM (Viton) seal, which is suited for compressed air, oils, fuels and many other chemicals. For hot water (>100°C), steam and alkaline substances EPDM is recommended instead of FKM.
Please consult the chemical resistance chart for other media.
The coil (type CS1-230AC) DIN - A with connector is provided with the valve. Other connector types, such as with an LED indicator can be ordered separately. The coil can easily be mounted on the valve. Never connect the coil to the power supply when it is not mounted on the valve to prevent the coil burning out.
Solenoid valves are electrically controlled valves which open or close by means of an electric current through a solenoid (coil). As long as they are electrically energized they consume energy. They open and close quickly. They are sensitive to dirt and can only be used with clean liquids or gases.
- Use clean liquids or gases. Solenoid valves are very sensitive to dirt.
- Do not power the coil when the coil is removed from the valve. The coil will overheat and may burn out.
- Make sure that the valve is suitable for the application and that the materials are suitable for the medium and temperature.
|Solenoid Valve||Electromechanically operated valve. An electric current through a solenoid is used to open or close the valve.|
|Direct operated||The solenoid pulls a ferromagnetic plunger. This will open or close the orifice directly. No differential pressure is required (operates from 0 bar).|
|2/2-Way||2 ports (inlet and outlet) and 2 positions (open and closed).|
|Normally closed||The valve opens when the coil is energized (Normally Closed or NC).|
|FKM||FKM (viton) is used for the seal material. FKM is suitable for (compressed) air, oils, fuels and other chemicals. FKM is more chemically resistant and can resist higher temperatures than NBR. EPDM is recommended for hot water (100°C+), steam and alkaline substances. View the materials compatibility overview.|
|230V AC||230 volt AC (50Hz). For most valve types different coils are available (380VAC, 230VAC, 120VAC, 24VAC, 12VDC, 24VDC). Always use the correct power supply.|
|Kv-value||Flow (m3/h) water of 20°C through the valve at a 1 bar pressure drop. The flow can be calculated with the formula: Q=Kv√dp. Example: The flow of a valve with Kv=0.5 in a system with a 2 bar inlet pressure and a free outlet can be calculated with: 0.5√2=0.7 m3/h, or 12 liter/min. For gases another formula must be used, the flow rate will be higher. A handy tool to determine the required Kv value is our Valve Sizing Calculator.|
|1/8 inch||G1/8 inch pipe thread (BSPP). Determine the valve size based on the desired flow rate and pipe diameter. Using the range of fittings, you can connect the valve to the desired type of pipe.|
ConnectorDIN - A