Max pres

Kv

Orifice

oil & fuel technology

For the most oils and fuels, a brass solenoid valve with FKM seals is a good choice. Solenoid valves can be direct or indirect operated. For indirect operated valves, a pressure difference is required across the inlet and outlet of typically... Read more Read more

Product Brand Port Voltage Seal Housing Function Operation Min pres Max pres Kv Orifice Max temp Power Series IP Torque Min temp State Connector Coil T/L Port
Electrical Ball Valve BW2...
$74.23 incl VAT
In stock
JP Fluid Control 3/4 inch 230V AC PTFE Brass 2 way Open-Close 0 10 21 15 110 5W BW IP54 4 -10 - - - -
Electrical Ball Valve BW2...
$64.95 incl VAT
In stock
JP Fluid Control 1/2 inch 230V AC PTFE Brass 2 way Open-Close 0 10 8.6 12 110 5W BW IP54 4 -10 - - - -
Electrical Ball Valve BW2...
$92.79 incl VAT
In stock
JP Fluid Control 1 inch 230V AC PTFE Brass 2 way Open-Close 0 10 26 20 110 5W BW IP54 4 -10 - - - -
Solenoid Valve ST-SA 1/2''...
$42.91 incl VAT
In stock
JP Fluid Control 1/2 inch 230V AC FKM Brass 2/2 way Semi-direct 0 16 1.49 10.5 120 17VA ST IP65 - -10 Normally closed DIN - A CS1 -
Electrical Ball Valve BW2...
$64.95 incl VAT
In stock
JP Fluid Control 1/2 inch 24V DC PTFE Brass 2 way Open-Close 0 10 8.6 12 110 3W BW IP54 2.5 -10 - - - -
Electrical Ball Valve BW3...
$97.43 incl VAT
In stock
JP Fluid Control 1 inch 230V AC PTFE Brass 3 way Open-Close 0 10 16 18 110 5W BW IP54 4 -10 - - - T-bore
Solenoid Valve CM-DA 1/4''...
In stock
JP Fluid Control 1/4 inch 12V DC FKM Brass 2/2 way Direct 0 10 0.11 2 120 6W CM IP65 - -10 Normally closed DIN - B CS4 -
Solenoid Valve CM-DA 1/4''...
In stock
JP Fluid Control 1/4 inch 230V AC FKM Brass 2/2 way Direct 0 13 0.11 2 120 8VA CM IP65 - -10 Normally closed DIN - B CS4 -
Electrical Ball Valve BW2...
$64.95 incl VAT
In stock
JP Fluid Control 1/2 inch 12V DC PTFE Brass 2 way Open-Close 0 10 8.6 12 110 3W BW IP54 2.5 -10 - - - -
Solenoid Valve ST-DA 1/8''...
$26.09 incl VAT
In stock
JP Fluid Control 1/8 inch 12V DC FKM Brass 2/2 way Direct 0 13 0.2 3 120 13W ST IP65 - -10 Normally closed DIN - A CS1 -
Electrical Ball Valve BW2...
$92.79 incl VAT
In stock
JP Fluid Control 1 inch 24V DC PTFE Brass 2 way Open-Close 0 10 26 20 110 3W BW IP54 2.5 -10 - - - -
Electrical Ball Valve BW2...
$74.23 incl VAT
In stock
JP Fluid Control 3/4 inch 24V DC PTFE Brass 2 way Open-Close 0 10 21 15 110 3W BW IP54 2.5 -10 - - - -
Electrical Ball Valve BW2...
$92.79 incl VAT
In stock
JP Fluid Control 1 inch 12V DC PTFE Brass 2 way Open-Close 0 10 26 20 110 3W BW IP54 2.5 -10 - - - -
Electrical Ball Valve BW2...
$74.23 incl VAT
In stock
JP Fluid Control 3/4 inch 230V AC PTFE Brass 2 way 3-point 0 10 21 15 110 5W BW IP54 4 -10 - - - -
Electrical Ball Valve BW3...
$97.43 incl VAT
In stock
JP Fluid Control 1 inch 230V AC PTFE Brass 3 way 3-point 0 10 16 18 110 5W BW IP54 4 -10 - - - T-bore
oil & fuel technology

oil & fuel technology | Tameson

For the most oils and fuels, a brass solenoid valve with FKM seals is a good choice. Solenoid valves can be direct or indirect operated. For indirect operated valves, a pressure difference is required across the inlet and outlet of typically 0.5 bar. In a closed circulating circuit, or a suction line, the differential pressure is usually too low. In this case, a (semi-)direct operated solenoid valve is recommended. Solenoid valves are suitable for clean liquids and gases. For contaminated media such as waste oil, other valve types such as (electric) ball valves, are more appropriate. Finally, solenoid valves are unsuitable for liquids with a high viscosity (higher than 50 Centistokes or mPa·s). Therefore, other valve types, such as electric ball valves, are better suited for viscous liquids such as heavy oils and fats.